Types of Hygienic Valves: Criteria for Choosing the Right Valve

  • Blog
  • Types of Hygienic Valves: Criteria for Choosing the Right Valve
Types of Hygienic Valves: Criteria for Choosing the Right Valve
Share

Types of Hygienic Valves: Criteria for Choosing the Right Valve

Table of Contents

  • What Is a Hygienic Valve?
  • Diaphragm Valves
  • Butterfly Valves
  • Ball Valves
  • Double-Seat (Mix-Proof) Valves
  • Sampling and Special-Purpose Valves
  • Criteria for Selecting a Valve
  • Points to Watch During Installation
  • Valve Maintenance and Spare Parts Planning
  • Conclusion

In hygienic process lines, a valve is not simply an element that opens and closes flow. A poorly chosen valve can mean uncleanable cavities, product residue, leaks and even a risk of cross-contamination. In this article we review the main types of hygienic valves used in food, pharmaceutical and biotech plants and the criteria to consider when selecting them.

What Is a Hygienic Valve?

A hygienic valve is designed so that its product-contact surfaces are smooth and its internal geometry is cleanable and drainable. Pockets, threads and sharp corners where product could accumulate are minimised. The body material is usually 316L stainless steel, while seals are selected from polymers suited to the process and to the cleaning chemicals.

Another important feature of hygienic valves is their suitability for cleaning-in-place (CIP) and sterilisation-in-place (SIP). The valve must allow cleaning solution to reach all internal surfaces and must withstand steam sterilisation temperatures.

Diaphragm Valves

Diaphragm valves are the most widely used valve type in sterile and pharmaceutical processes. Flow is shut off by pressing a flexible diaphragm onto a weir in the body. Because the moving mechanism stays behind the diaphragm, it never contacts the product. This design offers low dead volume and easy cleaning.

When installed at the correct angle, diaphragm valves also allow the line to drain completely. They are therefore regarded as the standard solution for purified water, water for injection (WFI) and sterile product lines. The point to watch is that the diaphragm must be inspected and replaced periodically.

Butterfly Valves

Hygienic butterfly valves are common in the food and beverage sector. Their simple construction, compact size and reasonable cost make them a popular choice, especially on large-diameter lines. The disc rotates on a shaft to open or close the flow, and sealing is achieved with a seat in the body.

Butterfly valves suit on/off duty but are not ideal for precise flow control. The area between the shaft and the seat should also be assessed carefully in sterile applications where product risk is high.

Ball Valves

Although ball valves are very common in industry, their use in hygienic applications is limited. The reason is that the cavity between the ball and the body is difficult to clean. Models designed specifically for hygienic service, with a filled cavity or a cleaning port, are available. They are generally used on auxiliary lines that do not contact the product directly, such as cleaning chemical or utility water lines.

Double-Seat (Mix-Proof) Valves

Double-seat valves allow two different fluids to pass through intersecting lines without mixing. They have two independent sealing surfaces with a leakage chamber in between. Any leak is discharged from this chamber, so product and cleaning solution never mix. They are preferred especially in dairy and beverage plants where one line must be cleaned while production continues on another.

Sampling and Special-Purpose Valves

Tank bottom valves, sampling valves and safety valves are also important parts of hygienic piping. Tank bottom valves allow the tank to drain completely without leaving dead volume at the bottom. Sampling valves are designed to take a representative sample without contaminating the product and can often be steam-sterilised on their own.

Criteria for Selecting a Valve

  • Product risk: diaphragm valves stand out for sterile or injectable products; butterfly valves may be sufficient on lower-risk food lines.
  • Cleaning and sterilisation: the valve must withstand the CIP chemicals and SIP temperature applied.
  • Drainage: the valve type and mounting angle must not prevent the line from draining.
  • Control requirements: for automated valves, the actuator, position feedback and compatibility with the control system should be assessed.
  • Ease of maintenance: seal and diaphragm replacement should be possible without dismantling the line, or with minimal intervention.
  • Documentation: material certificates, surface roughness and elastomer compliance documents should be added to the turnover package.

Points to Watch During Installation

Correct installation is as important as correct selection. If diaphragm valves are not installed at the drain angle, liquid remains inside the valve. A branch between the valve and the main line that is longer than necessary creates dead volume. For automated valves, the actuator must also be accessible for maintenance, and cable routes should be arranged so they do not contaminate the hygienic zone.

In our hygienic piping installation work, SS Proje determines valve positions during 3D design and checks drain angles and branch lengths before installation. This approach reduces corrections on site and the time lost with them.

Valve Maintenance and Spare Parts Planning

The performance of hygienic valves depends on regular maintenance. Diaphragms, gaskets and seal rings should be replaced after a certain number of cycles or a certain period. This interval is set according to process temperature, cleaning frequency and the chemicals used. Keeping spare parts for critical valves on site and recording each replacement helps prevent unexpected stoppages.

Conclusion

Hygienic valve selection gives the right result when product risk, cleaning method, control needs and maintenance conditions are assessed together. Each valve type has an application area where it performs best, and a single type may not be the best solution for the whole plant. To review the valve selection and layout in your plant together, you can talk to our project consultancy team or contact us.