How Much Product Stays in the Line? Product Recovery with Pigging Systems

  • Blog
  • How Much Product Stays in the Line? Product Recovery with Pigging Systems
How Much Product Stays in the Line? Product Recovery with Pigging Systems
Share

How Much Product Stays in the Line? Product Recovery with Pigging Systems

Table of Contents

  • What Is Pigging and Why Is It Used?
  • Why Product Left in the Line Matters
  • Pig Types and Application Areas
  • Launcher and Receiver Design
  • Pressure and Flow Control
  • Automation Levels: Fully Automatic, Semi-Automatic and Manual
  • ATEX and Area Safety
  • Integration with CIP and Cleaning
  • Commissioning and Site Checks
  • Conclusion

When a process line switches from one product to another, the product left inside the pipe causes both product loss and extra cleaning work. Pigging solves this by pushing a pig through the line to move the residue to a collection point. Pigging (Product Recovery) Systems make this operation safe and controllable.

What Is Pigging and Why Is It Used?

Pigging is the process of pushing a cylindrical or specially shaped element, called a pig, through a pipeline with pressurised fluid so that it sweeps the residue from the inner wall. It is used for line cleaning, product separation and controlled product recovery.

The main advantage is that the line can be emptied without being dismantled or fully flushed. On long or heavily bent runs, the amount left after a batch can be too large to drain by hand. The pig moves this volume to a collection point in one controlled stroke.

Why Product Left in the Line Matters

Every litre left in the pipe is a direct product loss and a contamination risk for the next batch. When the product is valuable, this loss shows up directly in raw material cost.

Residue also lengthens the rinse before CIP and increases water, chemical and energy use. Measuring the residual volume and bringing it down to a target value is therefore an important control point for process efficiency.

Pig Types and Application Areas

Different pig types suit different duties. Foam pigs perform well in lines with variable diameters because of their flexibility. Bullet-type pigs, which are rigid, use the pressure difference more efficiently in lines with a more constant bore.

Separator pigs are used to divide two different fluids. They form a barrier between the products and reduce mixing. The right pig type depends on line diameter, bends, fluid viscosity and cleaning expectations. The manufacturer's compatibility chart should be the first reference.

Launcher and Receiver Design

The pig launcher and receiver assembly is designed to insert and retrieve the pig. The positions of these two points must match the main line geometry, and enough space must be left for the pig to be loaded and unloaded easily.

The receiver includes sensors that detect the arriving pig and a vessel or tank that collects the product. Door and locking mechanisms should be designed so that they cannot be opened under pressure, which protects operators. Sealing elements should be selected from materials compatible with the process fluid.

Pressure and Flow Control

Pig movement is driven by the pressure difference along the line. If pressure is too low the pig stalls; if it is too high the pig accelerates and the mechanical stress increases. Speed and pressure should therefore be limited with a controlled regulator or valve.

Pressure profile and flow rate should be monitored during the pig run. Valve positions should not change until the signal confirms that the pig has reached its expected point. This helps prevent both product loss and sudden pressure fluctuations in the line.

Automation Levels: Fully Automatic, Semi-Automatic and Manual

Pigging systems can be designed as fully automatic, semi-automatic or manual. In a fully automatic system, the PLC, sensors and valves work together, the steps run in a predefined sequence, and each step can be logged.

In a semi-automatic system the operator confirms some steps, while in a manual system the operator carries out the whole procedure. Production volume, staffing and traceability requirements drive the choice. More automation raises the initial investment but improves repeatability and record quality.

ATEX and Area Safety

During a pig run, product vapour, dust or an explosive gas mixture can form around the line. Equipment must therefore be selected according to the ATEX zone classification of the installation area. Every component, including motors, sensors, cables and valves, must match that classification.

Static electricity, friction and spark risks must also be assessed. Earthing connections, door interlocks and emergency stop buttons should be tested before operation. Safety requirements should be set by national regulations, the plant risk assessment and the judgement of a qualified engineer.

Integration with CIP and Cleaning

After pigging, the line is often cleaned through a CIP cycle. The pig empties most of the product, and then the CIP solution rinses the line. The order and timing of these two steps must be clearly defined in the process flow diagram.

The pig surface must also be clean. A dirty or worn pig can carry contamination into the next batch. Its material suitability for the application and its post-wash inspection should be included in the quality procedure.

Commissioning and Site Checks

During commissioning, pig passage signals, valve sequencing, pressure values and alarm logic should be checked one by one. A test pig should confirm that the line is clear and that the pig moves through without getting stuck.

On site, the amount of product left at the receiver should be measured and compared with the acceptance criterion. Results are recorded and used as a reference for future changes. Acceptance criteria should be set by the responsible team according to the product and the process.

Conclusion

Pigging is an effective way to reduce the product left at the end of a run, lower the cleaning load and make the process more controlled. The right pig type, a safe launcher and receiver design, and ATEX-compliant equipment form the basis of that result.

Before a system is built, line geometry, product properties and cleaning targets should be reviewed together. SS Proje supports the design, manufacture and installation of pigging systems to match the needs of each process line.