How Are Mixer Motors and Gearboxes Selected?

  • Blog
  • How Are Mixer Motors and Gearboxes Selected?
How Are Mixer Motors and Gearboxes Selected?
Share

How Are Mixer Motors and Gearboxes Selected?

Table of Contents

  • Core Data for Mixer Motor Selection
  • Viscosity and Density
  • Tank Volume and Agitator Geometry
  • Speed and Torque Relationship
  • Gearbox Type
  • Approach to Motor Power Calculation
  • Speed Control and Frequency Inverters
  • Ex or Hygienic Motor Requirements
  • Installation and Alignment
  • Conclusion

In a tank mixer, the motor and gearbox deliver the speed and torque the agitator needs. Motor power alone is not enough; the flow properties of the product, the tank geometry and the intended mixing effect must be considered together. A drive system chosen wrongly either leaves the mix inadequate or overloads and fails.

Core Data for Mixer Motor Selection

The most important inputs are the product viscosity, density, tank volume, agitator type, operating temperature and mixing objective. Without this data a correct drive cannot be selected. The process data forms the starting point for the design calculation.

In addition, whether the tank is open or closed, the operating pressure and ambient conditions influence the motor construction. This information should be collected in writing.

Viscosity and Density

As viscosity rises, the energy needed to mix the product also rises. Density influences how well solid particles stay in suspension and how much mixing is needed. With low-viscosity products, mixing is generally easier, while with high-viscosity products the agitator type and speed setting become more critical.

Viscosity can change with temperature. The selection should therefore be assessed at the most demanding operating temperature.

Tank Volume and Agitator Geometry

Tank volume and proportions, together with the diameter, position and type of the agitator, determine mixing efficiency. In large or deep tanks, several impellers may be needed instead of one. Propellers, turbines and anchors produce different flow patterns.

No fixed proportion is given for agitator geometry here. Tank and agitator dimensions should be reviewed together by the manufacturer and the process engineer.

Speed and Torque Relationship

As agitator speed increases, the torque and energy required also rise. In applications that need high torque at low speed, the gearbox ratio plays an important role. The speed-torque relationship should be verified with the agitator manufacturer's data and the design calculation.

The load at start-up can be higher than the running load. The motor and gearbox should therefore be assessed for their ability to handle starting torque as well.

Gearbox Type

Gearboxes come in helical, bevel-helical, planetary and worm designs, among others. Each type differs in efficiency, size, load capacity and maintenance needs. For top-mounted agitators, the structure and size of the gearbox become especially important.

The oil temperature limit, shaft load and sealing protection of the gearbox should also be assessed. Selection should be based on the manufacturer's catalogue and the application data.

Approach to Motor Power Calculation

Motor power is calculated taking into account the energy needed for mixing, efficiency losses and a safety margin. The calculation should be carried out with the product data and the agitator manufacturer's method. No general formula or fixed value is given in this article.

The calculated result is rounded up to a standard motor rating. When rounding, load variations and possible future capacity increases should also be considered.

Speed Control and Frequency Inverters

Where variable-speed operation is needed, a frequency inverter is used. This arrangement helps adjust speed through the different stages of a mix and reduces the start-up load. The inverter rating, motor current and cable length must be considered.

For motors that may have cooling problems at low speed, compatibility with the inverter and the motor cooling conditions should be checked separately.

Ex or Hygienic Motor Requirements

Motors used where flammable vapour or dust is present must suit the relevant ATEX zone classification. In food and pharmaceutical applications, the motor and gearbox surfaces should be cleanable and designed to be compatible with the product. Both requirements can apply at the same time.

The requirements should be set together with the plant risk assessment and the applicable regulations. The information on the motor nameplate should be compared with the installation area.

Installation and Alignment

The alignment between the agitator shaft and the motor-gearbox axis directly affects bearing and shaft life. Misalignment leads to vibration and early failure. Installation should follow the manufacturer's tolerances and be recorded.

The mounting platform on the tank must be rigid enough to withstand vibration. The installation of the shaft seal should also be checked separately.

Conclusion

Selecting a mixer motor and gearbox should weigh viscosity, density, tank geometry, speed-torque relationship, speed control and environmental requirements together. Collecting the data correctly and verifying the calculations with the manufacturer's method makes mixing performance predictable.

SS Proje supports the design and manufacture of mixer and tank systems with drive solutions matched to process requirements.